Strength and deformation properties of frozen sand under a true triaxial stress condition

In recent years, the mechanical properties of frozen soils under complex stress states have attracted significant attention; however, limited by the test apparatus, true triaxial tests on frozen soils have rarely been conducted. To study the strength and deformation properties of frozen sand under a true triaxial stress state, a novel frozen soil testing system, i.e., a true triaxial apparatus, was developed. The apparatus is mainly composed of a temperature control system, a servo host system, a hydraulic servo loading system, and a digital control system. Several true triaxial tests were conducted at a constant minor principal stress (σ₃) and constant intermediate principal stress ratio (b) to study the effect of intermediate principal stress (σ₂) on the mechanical properties of frozen sand. The test results showed that the stress–strain curve can be mainly divided into three stages, with evidence of strain hardening characteristics. The strength, elastic modulus, and friction angle increased with the increase in b from 0 to 0.6, but decreased when increasing b from 0.6 to 1, whereas the cohesion varied little with the variation in b. The deformation in the direction of σ₂ changed from dilative to compressive and that in the direction of σ₃ remained dilative throughout.     

Evaluation of back-calculated elastic moduli of unreinforced and geocell-reinforced unbound granular material from full-scale field tests

This paper presents a field-scale experimental track over a poor subgrade with an unreinforced section and a geocell-reinforced section subjected to in-situ performance tests. Plate load tests and Benkelman beam tests were carried out distributed in several unreinforced and reinforced layers. The objective was to: (1) examine the variability of the elastic modulus of unbound granular material (UGM) due the influence of its thickness and the presence of poor subgrade in its base, (2) evaluate the modulus improvement factor (MIF) generated by the geocell reinforcement in the UGM and (3) verify the most appropriate condition to apply the MIF to transport infrastructure design. The results showed that there is a significant influence of the thickness of the UGM layer on its elastic modulus when the layer is supported directly over a soft subgrade. The MIF values obtained in field suggest that its determination is mostly related to the UGM maximum elastic modulus rather than its decreased values (by virtue of poor subgrade or reduced thicknesses), and that the analytical formulation presented for MIF calculation has good predictive capability to be applied to pavement design.     

Tribological and mechanical characteristics of AA5083 alloy reinforced by hybridising heavy ceramic particles Ta2C & VC with light GNP and Al2O3 nanoparticles

In this study, AA5083 sheets were reinforced with four different hybrid nanoparticles by friction stir processing (FSP) for the development of surface nanocomposites used in advanced engineering applications. The present research focused on improving the properties and tribological behaviour of AA5083 alloy surfaces, including novel hybrid nanoparticles and the intermetallic phase formed during FSP. A tribometer tester with a constant normal load was used to examine the tribological performance of the hybrid composites. After the wear test, a surface profiler inspector was used to analyse the morphology and surface roughness of the examined materials. The Vickers micro-hardness of the base metal and the manufactured composites were measured. During FSP, a new intermetallic phase of AlV₃ was successfully formed at 300–400 °C in the hybrid nanocomposites containing VC particles. The reinforcements resulted in additional grain refining than FSP. The AA5083/Ta2C–Al₂O₃ exhibited the greatest grain refinement, a sixty-fold reduction in grain size compared to that of the base alloy. The results revealed that the hybrid nanocomposites containing VC particles demonstrated the most significant microhardness values inside the stirred zone as a result of the presence of the AlV₃ phase, which was increased by 25–30%. Moreover, the mechanical properties were significantly improved for all manufactured nanocomposites. The tensile strength was increased by 28% through the hybridisation of AA5083 using a hybrid of VC-GNPs. The dispersion of Ta₂C-GNPs and VC-GNPs in the matrix led to excellent interfacial adhesion, resulting in an enhancement in the mechanical properties. The AA5083/VC-GNPs surface composite outperformed other manufactured composites regarding wear resistance. In addition, due to GNPs soft nature, it reduced the coefficient of friction (COF) of the manufactured composites by 20–25% compared to other reinforcements.     

Synthesis of Diamond@SiO2@Ag composite materials for high SERS effect

Among various carbon materials, diamond stands out due to excellent physical and chemical properties. In this work, we designed Dia@SiO₂@Ag composites combining diamond micropowder and Ag nanoparticles by a simple chemical method and obtained stable substrate for surface enhanced Raman scattering (SERS) owing to its high surface-to-volume ratio, low density, as well as close bond between diamond and Ag. As-prepared Dia@SiO₂@Ag presented high activity to detect crystal violet and rhodamine 6G molecules, which was demonstrated by significantly enhanced SERS spectra and high enhancement factor values (10⁸-10⁹). Moreover, Dia@SiO₂@Ag also showed desired sensitivity, which was investigated by detection limit. Therefore, our study provided more theoretical support and broadened the functional applications of diamond, particularly in Raman detection.     

Negative thermal quenching CsPbBr3 glass-ceramic based on intrinsic radiation and vacancy defect co-induced dual-emission

Halide perovskite glass-ceramic has recently moved into the center of the attention of perovskite research due to their potential for temperature sensing. However, quantum dots glass-ceramic with excellent luminescence performance still needs to be combined with rare-earth (RE) ions to accurately measure temperature. In this work, a novel non-RE doped dual-emission (460 nm and 512 nm) CsPbBr₃ quantum dots was obtained in telluride glass via the friction crystallization method, where 512 nm was derived from intrinsic luminescence of quantum dots, and 460 nm was originated from thermally induced bromine vacancy, which can be used for temperature sensing. Fluorescence intensity ratio results indicate that the relative sensitivity of dual-emission could reach 5.6 % K^?1 at 323 K. The discovery of non-RE doped CsPbBr₃ QDs glass-ceramic with negative thermal quenching uncovers a new optional sensing glass material that surpass traditional RE-doped QDs glass by their tunability and sensitivity.     

抗FGF-2纳米抗体抑制碱烧伤诱导大鼠角膜血管新生

目的：研究抗成纤维细胞生长因子（FGF-2）纳米抗体对碱烧伤诱导的大鼠角膜血管生成的治疗作用。方法：将SD大鼠分为：假手术组（Sham），模型组（Model，直径为3 mm的浸有1 mol/L NaOH溶液圆形滤纸贴于大鼠眼角膜中央处30 s，制备大鼠碱烧伤血管生成模型）和治疗组（Treatment，术后7天至21天用3 mg/mL的抗FGF-2纳米抗体溶液滴眼，每日3次，每次10 μL，共14天）。通过体视显微镜和CD31免疫组织化学染色计算大鼠角膜血管生成情况。实时荧光定量PCR、酶联免疫吸附测定和免疫组织化学染色3种方法检测抗血管内皮生长因子（VEGF）和FGF-2的mRNA和蛋白表达水平。结果：（1）血管：治疗组较模型组的面积显著减少，血管管腔较窄（P<0.05），在药物干预14天后，差异最为显著；（2）FGF-2的mRNA和蛋白表达水平：模型组与治疗组的结果相近（P>0.05）；（3）VEGF的mRNA和蛋白表达水平：治疗组显著高于模型组（P<0.05）。此外，假手术组的持续给药也使得VEGF表达显著增加（P<0.05）。 结论：抗FGF-2纳米抗体可抑制由碱烧伤诱导的角膜血管新生，但也使得正常大鼠角膜或病理大鼠角膜的VEGF表达水平代偿性升高。     

Testing EGFR with Idylla on Cytological Specimens of Lung Cancer: A Review

The current standard of care for advanced non-small-cell lung cancer is based on detecting actionable mutations that can benefit from targeted therapy. Comprehensive genetic tests can have long turn-around times, and because EGFR mutations are the most prevalent actionable mutation, a quick detection would enable a prompt initiation of targeted therapy. Furthermore, the scarcity of diagnostic material means that sometimes only cytologic material is available. The Idylla™ EGFR assay is a real-time PCR–based method able to detect 51 EGFR mutations in 2.5 h. Idylla is validated for use only on FFPE sections, but some researchers described their experiences with cytological material. We reviewed the relevant literature, finding four articles describing 471 cases and many types of cytological input material: smears, cell-block sections, suspensions, and extracted DNA. The sensitivity, specificity, and limit of detection appear comparable to those obtained with histological input material, with one exception: the usage of scraped stained smears as input may reduce the accuracy of the test. In conclusion, usage of cytological material as input to the Idylla EGFR test is possible. A workflow where common mutations are tested first and fast, leaving rarer mutations for subsequent comprehensive profiling, seems the most effective approach.     

Improving the fill factor of N2200-based all polymer solar cells by introducing EPPDI as a solid additive

A cheap and commercially available small molecule (namely EPPDI) is introduced to the active layer of N2200-based all polymer solar cells as a solid additive. EPPDI at the optimal ratio can improve the D-A nano-scale morphology and reduce trap density of the active layer by filling morphological spaces. As a result, the photovoltaic performance of the resulting devices based on PF2:N2200 are increased from 6.28% to 7.03% with significantly enhanced fill factor. This work demonstrates a facile approach for improving the performance of all polymer solar cells.     

Strong tribocatalytic dye degradation by tungsten bronze Ba4Nd2Fe2Nb8O30

The triboelectric effect has recently demonstrated its great potential in environmental remediation and even new energy applications for triggering a number of catalytic reactions by utilizing trivial mechanical energy. In this study, Ba₄Nd₂Fe₂Nb₈O₃₀ (BNFN) submicron powders were used to degrade organic dyes via the tribocatalytic effect. Under the frictional excitation of three PTFE stirring rods in a 5 mg/L RhB dye solution, BNFN demonstrates a high tribocatalytic degradation efficiency of 97% in 2 h. Hydroxyl radicals (?OH) and superoxide radicals (?O₂－) were also detected during the catalysis process, which proves that triboelectric energy stimulates BNFN to generate electron-hole pairs. The tribocatalysis of tungsten bronze BNFN submicron powders provides a novel and efficient method for the degradation of wastewater dye by utilizing trivial mechanical energy.     

Wear resistance and hardness properties of TiB2– Fe coating developed on AISI 1020 steel by tungsten inert gas (TIG) cladding

The present work is attempted to improve the microhardness and wear properties of AISI 1020 steel by depositing TiB₂–Fe composite coating using tungsten inert gas (TIG) cladding. In this study, different compositions of TiB₂–Fe paste form were preplaced on the substrate plates and then TIG heat input was applied to deposit hard composite coating layer. The main objective of the present work was to explore the influence of TIG input current as well as iron content on the microstructure and surface properties of deposited coatings. Microhardness, microstructural and phase characterization of the coating have been done by the Vickers microhardness tester, scanning electron microscope (SEM), Energy dispersive spectroscopy (EDS) and X-ray diffractrometer (XRD). The results showed that the microhardness of the TiB₂–Fe coating was strongly influenced by the composition of the coating materials as well as the TIG processing current. The microhardness increases with decreasing Fe contents in the coating materials with constant processing current (90 A) as well as it also increases with decreasing processing current with the fixed composition of coating materials (80TiB₂–20Fe). The maximum average microhardness found was 3082 HV_0.1 for the coating of 100TiB₂–0Fe composition ratio and 90 A processing current which was about 18 times higher than that of the substrate average microhardness value (163 HV_0.1). Average wear rate evaluated by considering weight loss of the TIG cladded samples using pin on disc tribometer by the sliding distance of 864 m and 20 N normal loads. The wear results also showed that the coating contains 100 wt% of TiB₂ (0 wt% of Fe) exhibited lower rate of wear 6.74 × 10^?8 g/Nm which is about 24 times lower as compared to AISI 1020 mild steel wear rate (166.31 × 10^?8 g/Nm).